Recent content by mpwolf

  1. M

    WTT Tikka mag bolt for .223 bolt

    still looking.
  2. M

    WTT Tikka mag bolt for .223 bolt

    still looking
  3. M

    WTT Tikka mag bolt for .223 bolt

    I have a T3 magnum bolt. Would like to trade for a .223 bolt. Preference would be for one with a larger knob.
  4. M

    WTS Shorty .300 WSM Tikka prefit

    found a local guy to turn it down. off the market
  5. M

    WTS Shorty .300 WSM Tikka prefit

    bump- for pics added
  6. M

    WTS Shorty .300 WSM Tikka prefit

    Shouldered McGowen 300 WSM, 18" 1-9, threaded 5/8-24, heavy contour. Bought this on the Hide back in December. I thought it was a Remington magnum sporter contour, but it's much heavier than that- more like heavy varmint. Original seller says it has roughly 150 rounds on it. I spun it onto my...
  7. M

    Sold Mesa/Pure Precision Tikka T3X RH carbon stock

    I'll take it. PM sent
  8. M

    6.5 saum with 7 saum adg brass

    Yup- my reamer is .2964" and even though my loaded round is .291, a bullet still won't drop freely into a fired case. Makes me think the PTG spec is likely off a smidge. Let your actual fired case tell the story. Turning necks is a pain, but once it's done and you have your brass at a healthy...
  9. M

    6.5 saum with 7 saum adg brass

    B23 is spot on, but I would aim for more clearance if you can. In my experience, you are better off with a bit extra clearance, than just barely enough.
  10. M

    6.5 SAUM

    Thanks guys. Rifle was chambered with one of the earlier GA Prec. spec reamers. Initial loads were with a very old lot of H1000, and I couldn't get 140 amax above 2650 fps! At the time, I didn't have any other suitable powder, so I just loaded up the cases I had prepped and shot them over the...
  11. M

    Sold Tikka 300 wsm prefit 18”,stainless action, ADG brass

    I'll take the barrel and brass. PM sent
  12. M

    6.5 SAUM

    I built up a 6.5 Saum a while back. 22" Brux 1-8.5" #3 contour, on a Rem 700 SA. At the time, Rem brass was all that was availble, so I converted 100pcs of .300 SAUM brass. At this point I have fired those 100cases, and I'm ready to seriously start working on a load. I have RL26, H1000, H4831SC...
  13. M

    Which full length resizer die to get?

    I really like Forster FL dies. The expander ball is just the right shape to slide throught the neck easily, making for smooth sizing. Having said that, I would definitly contact Hornie about the issue with your current die.
  14. M

    Velociradar vs. Labradar LX vs. Garmin Xero

    I have had my LR since 2017. It was always pretty inconsistent until I got the external trigger, which helped quite a bit, but still didn't make it completely reliable. I'm surprised to hear that some units seem to be much more consistent at capturing shots than others. I'm not going to replace...
  15. M

    Velociradar vs. Labradar LX vs. Garmin Xero

    Something else to consider- Labradar is not known for customer service.
See more

Latest posts

Featured Video

Stats

Threads
324,467
Messages
3,408,059
Members
75,376
Latest member
ca-hunter

Latest Articles

Top