Search results
-
J
WTB 300wsm bushing dies
Found a sizer, still looking for a seater. Prefer a micrometer style- JJMoody
- Post #5
- Forum: Guns Classifieds
-
J
WTB 300wsm bushing dies
Lemme know if ya got a set hanging around- JJMoody
- Thread
- Replies: 5
- Forum: Guns Classifieds
-
J
WTS Kelbly Nanook lapua bolt
PMs responded to. Still available.- JJMoody
- Post #5
- Forum: Rokslide Classifieds
-
J
WTS Kelbly Nanook lapua bolt
☝️ don’t listen to that guy, he’s known to hang around all sorts…..😂- JJMoody
- Post #3
- Forum: Rokslide Classifieds
-
J
WTS Kelbly Nanook lapua bolt
Selling a BNIB never had a bbl on nanook with lapua bolt face ( kelblys said they could swap to mag etc if unfired and so desired). I switched up build plans, so this is up for grabs. $1300 shipped to your FFL from FFL. Let me know if you have any questions. Plenty of feedback on LRH/SH/accurate...- JJMoody
- Thread
- Replies: 5
- Forum: Rokslide Classifieds
-
J
Sold Ruger security six .357 +ammo
recent trade acquisition, great shape. Doesn’t appear to have been fired much. Only wear looks like tip of the muzzle and front of the cylinder. Probably mostly just holster wear. comes with 97 HSM factory blemish 180 gn bear loads and box of 50 110gn hollow point ammo, and a Galco leather...- JJMoody
- Thread
- Replies: 0
- Forum: Rokslide Classifieds
-
J
WTS DE 338 Edge +p BAT
Any chance one of the moderators can move this to guns section?- JJMoody
- Post #2
- Forum: Rokslide Classifieds
-
J
WTS DE 338 Edge +p BAT
Putting this out there again... Zero rounds fired BAT HR single shot Rock Creek spiral fluted 9.4 twist at 31”+brake Manners T2 adjustable Huber 2 stage flat shoe 338 edge +p by Defensive Edge Cerakote titanium 12.8# as pictured $3950 shipped and insured Located in Post Falls, Idaho Posted...- JJMoody
- Thread
- Replies: 2
- Forum: Rokslide Classifieds
-
J
Sewing machine upgrade time
Started leather stitching on an old 29-k treadle machine..... brings back memories...- JJMoody
- Post #5
- Forum: DIY Gear Modifications
-
J
Modifying tyvek, specifically adding loops or tie downs
I’ve never done it with tyvek, but one idea might be to stitch something more durable (leather) to the corners using plenty of contact cement and punch a hole in the reinforced area to attach grommets- JJMoody
- Post #2
- Forum: DIY Gear Modifications
-
J
Free leather scraps in north Idaho
Ok, so the original intent here was to allow someone who needed a bit or a lot of something for a project and scrap would work. They could dig through some stuff I most likely won’t use, but can’t bring myself to toss out and they could do it for free. —mutual benefit and “pay it forward” to the...- JJMoody
- Post #5
- Forum: DIY Gear Modifications
-
J
Sold 338 cal 300 smk or Berger
Ain’t that the truth... thanks to all, I found what I needed.- JJMoody
- Post #6
- Forum: Guns Classifieds
-
J
Sold 338 cal 300 smk or Berger
Local shop here had em for $375ish/500 last week... should have pulled the trigger. Bachelor Jack, I’m gonna hold off on that offer and keep looking. Thanks for the offer though.- JJMoody
- Post #4
- Forum: Guns Classifieds
Featured Video
Stats
Latest Articles
-
TT#28 Idaho Bear Hunting with Roger Holscher and Chris Young
-
Rockstar Research with Kevin Monteith
-
Hunting Big Mule Deer: Obey the Wind & Still-Hunting
-
TT#27 DIY New Zealand Hunting with Australian Duo Miller and Pitts
-
Fewer Bucks, More Fawns?
-
Mathews Lift Review
-
Wyoming Range Winter Wrap-Up with Jeff Short
-
The Pursuit with Cliff Gray
-
Mile High Mule Deer Seminar
-
TT#26 Kyle Virgin and the infamous Hobbit Rifle