300 WSM Barrel Length Help

cfish4422

FNG
Joined
Feb 28, 2021
Messages
58
What did you have your barrel threaded to? I'm looking at doing exactly this to a 300 wsm t3x SS superlite or t3x SS lite (whichever I can get my hands on first), then throwing my suppressor on it. I have read differing opinions on there being enough meat on these specific barrels to thread and get enough of a shoulder for a suppressor.
 

308ghost

FNG
Joined
Mar 11, 2020
Messages
33
What did you have your barrel threaded to? I'm looking at doing exactly this to a 300 wsm t3x SS superlite or t3x SS lite (whichever I can get my hands on first), then throwing my suppressor on it. I have read differing opinions on there being enough meat on these specific barrels to thread and get enough of a shoulder for a suppressor.
I went with 9/16″-24 on the 300WSM. I also have a 7mm rem mag tikka and did the 1/2X28 on that one because the bore was smaller and there was more steel. It has a little more shoulder for the mount to tighten up too but I check to make sure that thing is tight no matter what its on pretty frequently. I havent had any issues with it backing off the 300 WSM or the 7mm barrel. I also dont shoot long strings with these rifles and havent had any problems around the muzzle as of yet.
 
OP
J

Japes4

FNG
Joined
Aug 7, 2020
Messages
37
This has become a very useful and informative thread! After talking with my gunsmith, I ended up going with 2 1/2 cut off and 1/2 x 28 threads. Until my suppressor gets out of jail, I’ll be running the Area 419 Hellfire brake. I hope to work up rounds with TTSX to get velocity back up to 3000 - 3050. Maybe, someday, I’ll be as good behind the trigger as 308ghost and get get results like that out of the 300wsm!
 

cfish4422

FNG
Joined
Feb 28, 2021
Messages
58
This has become a very useful and informative thread! After talking with my gunsmith, I ended up going with 2 1/2 cut off and 1/2 x 28 threads. Until my suppressor gets out of jail, I’ll be running the Area 419 Hellfire brake. I hope to work up rounds with TTSX to get velocity back up to 3000 - 3050. Maybe, someday, I’ll be as good behind the trigger as 308ghost and get get results like that out of the 300wsm!
What is your barrel length after taking the 2.5 inches off? I'm waiting to get my hands on either a t3x lite from my local gun shop or a superlite from sportsmans, I'll buy whichever comes available first. Initially I thought I'd cut the lite down to 22 inches then thread, or just leave the superlite at 22 inches and thread, but after reading 308ghost's results I'm considering cutting down to 20 if I end up with a lite (20 is the shortest I can go with my can).
 

tdbaugha

FNG
Joined
Feb 3, 2021
Messages
61
You might want to consider cutting it again with 9/16 threads. TBAC won’t warranty a can that was mounted to 1/2” threads on a .308” caliber barrel. I ran the question by dead air for my 300 wyb and they said minimum would be 9/16” threads. TBAC has a nice chart showing thread dimensions and minimum shoulder OD.
 

Bak222

FNG
Joined
Dec 17, 2020
Messages
46
I planned to do this with a t3x lite. Now I can’t find one in stock. Do you know if barrel diameter permits a 5/8-24
 

cfish4422

FNG
Joined
Feb 28, 2021
Messages
58
I planned to do this with a t3x lite. Now I can’t find one in stock. Do you know if barrel diameter permits a 5/8-24
Check with member LEO Outfitters, he had a t3x lite and t3x lite stainless in 300wsm for sale not long ago.
 

Bak222

FNG
Joined
Dec 17, 2020
Messages
46
Check with member LEO Outfitters, he had a t3x lite and t3x lite stainless in 300wsm for sale not long ago.
Thanks. I saw he had a few blued, I didn’t see any stainless. I found one anyhow, I was signed up for in stock notifications and just bought one today!
 

madcalfe

WKR
Joined
May 9, 2019
Messages
902
Location
British Columbia
This thread is so inspiring that I had to sign up to the site ! Thanks Japes4.
I'm looking at doing something similar and want a shortish allrounder (22" + brake) that I can take deer with between 100-200yds and ring some steel at 600. I'm used to 300WM (too long) and 308...(not enough punch)

Don't want to hijack the thread but it appears you guys would know the best projectile to use for this caliber.
Anyone using Hornady InterBond 165s in 300WSM?
OR, anyone had a nightmare trying to get the 190 ABLRs to group ?
in my 20" barrel 300wsm im running 178gr eldx at 2920fps that gives me 1500ft-lbs at 650 yards.
ive also used the 190gr ALBR and 180 accubonds with good success.
for what your wanting to do you can probably use just about any decent bullet in the 165gr-200gr category
 

308ghost

FNG
Joined
Mar 11, 2020
Messages
33
in my 20" barrel 300wsm im running 178gr eldx at 2920fps that gives me 1500ft-lbs at 650 yards.
ive also used the 190gr ALBR and 180 accubonds with good success.
for what your wanting to do you can probably use just about any decent bullet in the 165gr-200gr category
You like those 178’s? I want to try those some time my self. Some RL 16 or 23 and a fed 210 would be killer I think. Do you think they shoot better than the 190 ABLR?
 

Lawnboi

WKR
Joined
Mar 2, 2012
Messages
7,686
Location
North Central Wi
This has become a very useful and informative thread! After talking with my gunsmith, I ended up going with 2 1/2 cut off and 1/2 x 28 threads. Until my suppressor gets out of jail, I’ll be running the Area 419 Hellfire brake. I hope to work up rounds with TTSX to get velocity back up to 3000 - 3050. Maybe, someday, I’ll be as good behind the trigger as 308ghost and get get results like that out of the 300wsm!
I’d re read some of the above and talk to your suppressor company about the thread.

A .308 cal barrel threaded 1/2” leaves only .096” of steel in the wall.

In regards to advise for future readers. Some of the most respected gunsmiths and suppressor manufacturers reccomend NOT threading a 308 barrel 1/2”.
 

tonechaser88

Lil-Rokslider
Joined
Feb 2, 2019
Messages
123
Was running a 20”(22” w brake) barrel 300 wsm shooting 212 eldx at 2775. Thing had some recoil but it’d hit hard hard . That was a fairly hot load but no signs of pressure.
 
OP
J

Japes4

FNG
Joined
Aug 7, 2020
Messages
37
Surprised to see this thread still going! Just to update, I went back and forth with my gunsmith regarding the 1/2” threading. He seemed very confident in it holding up, but I think I gave in a bit and should have pushed back more. I agree with previous posts and If I had to do it all over again, I’d take it to another smith that would jump up in thread size and use some thread adapters.

All that being said, the gun has shot great and been very reliable shooting some 168 gr TTSX hand loads at around 3010 FPS. Pleased with the length and feel of the gun.
80582012384259cb59e332820eccb7ec.jpg



Sent from my iPhone using Tapatalk
 

gilby

Lil-Rokslider
Joined
Feb 27, 2018
Messages
117
Location
Minnesota
After reading this thread and a few others several months ago I bought a Tikka 300wsm and had silencer central cut it down to 18" and threaded to 9/16-24. I put a radial brake on there while I wait for my TBAC to get out of jail.

The velocities I'm getting with H4350 are:
3039fps with HH160
2686fps with terminal Ascent 175
2648fps with accubond 180
 

tdhanses

WKR
Joined
Sep 26, 2018
Messages
5,721
After reading this thread and a few others several months ago I bought a Tikka 300wsm and had silencer central cut it down to 18" and threaded to 9/16-24. I put a radial brake on there while I wait for my TBAC to get out of jail.

The velocities I'm getting with H4350 are:
3039fps with HH160
2686fps with terminal Ascent 175
2648fps with accubond 180
Thats a pretty sharp drop in velocity, with a 26” barrel I’m getting 2963fps with 215’s out of my 300wsm.
 

madcalfe

WKR
Joined
May 9, 2019
Messages
902
Location
British Columbia
You like those 178’s? I want to try those some time my self. Some RL 16 or 23 and a fed 210 would be killer I think. Do you think they shoot better than the 190 ABLR?
Yea I have no complaints about the 178’s I’ve taken a couple mountain Goats, black bears, and elk with them and they have all stopped in their tracks with 1 shot.


Thats a pretty sharp drop in velocity, with a 26” barrel I’m getting 2963fps with 215’s out of my 300wsm.
I think going from 20-18” is where you see a huge drop in velocity, my ridge line (24”) I was getting 3025fps with 178gr where as my 20” I’m doing 2920 with h4350
 

Jimss

WKR
Joined
Mar 6, 2015
Messages
2,074
When I was looking for a lighter sheep, mtn goat/mtn rifle I had it narrowed down to Tikka or Sako. I ended up with a Sako Finnlight so is super light for hauling up and down the hills. It barely kick so no need for a suppressor/muzzlebreak!
 

T28w

WKR
Joined
Dec 10, 2018
Messages
585
Anyone care to share there 300wsm load recipes. I’m getting back out today to retest some loads. I have a thread discussing the issues already and would like to see what others are using brass and powder, and charge weights.
I don’t think I’m going to be happy with what I have loaded up today. Velocity is going to be too low I feel, but too much pressure signs where I was.
 

Lou400a

Lil-Rokslider
Joined
Sep 16, 2019
Messages
233
Location
SE Florida
I've started few latters on my 21" Fierce Fury (Sako 85) with 180gr Nosler BT Silvertip
Most accurate was H4350 followed by H4831 than Superformance which was least accurate of the bunch, but fastest

H4350_180BTS.pngH4831_180BTS.pngSuperformance_180BTS.pngff4.jpg
 
Last edited:

madcalfe

WKR
Joined
May 9, 2019
Messages
902
Location
British Columbia
Anyone care to share there 300wsm load recipes. I’m getting back out today to retest some loads. I have a thread discussing the issues already and would like to see what others are using brass and powder, and charge weights.
I don’t think I’m going to be happy with what I have loaded up today. Velocity is going to be too low I feel, but too much pressure signs where I was.
What bullet are you using?
H4350, H4831sc, and H100V will be the best powders,
 
Top