Recent content by kroskanyon

  1. K

    question on zess v4 capped windage

    Looking to get a v4 4-16 but with the reticle I want they dont seem to offer the exposed windage turret. For those that have the capped windage, do you use it for dialing wind or just holdover. With the capped windage the turret seems quite small. Curious on peoples thoughts. Thanks
  2. K

    Sold LH Tikka stock

    Pm sent
  3. K

    Advice on night vison scope with rangefinder

    I'd like to keep it under $1500 or so. Will I be able to identify the target animal inside 400 yards?
  4. K

    Advice on night vison scope with rangefinder

    Sure. I have a thermal scanner now and dont want to spend the 6-10k at the moment for a quality thermal scope with rangefinder.
  5. K

    Advice on night vison scope with rangefinder

    Looking to buy a night vision scope with rangefinder (not thermal) Is the pulsar n455 discontinued? Not looking for the cheapest rather one that works. Thanks
  6. K

    questions on revic BR4

    I am currently shooting berger bullets in all my LR guns. Vld's and hybrids
  7. K

    questions on revic BR4

    Ok so I got to play with this thing today. When I fire it up from sleep mode both base wind and vector wind are at zero, still no spin drift calculation. When I change the vector wind from zero to one or any number then back to zero again the rangefinder will give a solution for spin drift...
  8. K

    questions on revic BR4

    Yes it does appear to show spin drift on the app. Although my app is having some glitches. I assume setting the base wind to zero is turning it off..? Even at 2k yards no wind input on the rangefinder unless I enter a wind value. I will get a chance to play with it tomorrow morning out to...
  9. K

    questions on revic BR4

    Yes. I completed the gun profiles and synced the info to the rangefinder. Not sure whats going on.
  10. K

    questions on revic BR4

    When ranging with 0 base wind entered , spin drift and coriolis and aero jump turned on the rangefinder never gives a wind input no matter what the range. Is this normal? Doesn't seem like i should have to put in a wind input to get a solution from spin drift? Anyone else seeing the same...
  11. K

    What's happening here? (hard bolt lift)

    following..... having same issue 7 saum adg brass
  12. K

    7 saum whidden bushing question

    Thanks. Yes added a zero not paying attention... I put the expander ball back in and ran brass back through. All good. Not used to seeing near that much variation. Loaded rounds once fired brass are .316 Usually find the bushing i need and sand expander ball down so it's just a very slight...
  13. K

    7 saum whidden bushing question

    Reloading once fired 7 saum adg brass. Loaded rounds virgin brass measured .3015- .30155 . Redding type S bushig die. I have only used redding bushings in the past but couldn't find any so I bought a .313 and .314 from whidden. Expander ball removed. Tried the .314 first and it was sizing...
  14. K

    Sold Left Hand Mesa Precision Altitude Stock Tikka T3x Sporter

    pm sent
  15. K

    338 terminator +p barrel life

    I don't have a dog in this discussion but I'll share my experience. My 30 nosler had a 26" broughten steel barrel. My load was 84.4 grains n570 running a 215 @3120. Definitely the high node for this rifle but extremely accurate. Noticeable ejector mark but the nosler brass seemed very soft...
See more

Latest posts

Featured Video

Stats

Threads
322,967
Messages
3,391,182
Members
75,110
Latest member
baylorhenry

Latest Articles

Top