The Shoot2hunt Podcast

[Reburn]

Milk and fruit are why I will never do keto.

Sadly the need for low carb was chosen for me by gentics.

 

[Dunky]

After listening to the last podcast you guys should change the name. Maybe drop the OO in shoot, replace with an I

 

[Ryan Avery]

@Ryan Avery and @Unknown Munitions

Yall be careful with milk. It has quite a bit of carbs. You drink too much you will toss yourself out of ketosis.

Carbs In Milk

Regular full cream milk has 12g of carbs per cup but carbohydrate content differs between various milk products such as skim milk, cheese, and cream.

www.myketokitchen.com

I don’t like milk

Luke and I are the only ones left in the challenge.

 

[Ryan Avery]

Podcasting with ADG tomorrow

Any questions?

 

[Harvey_NW]

Podcasting with ADG tomorrow

Any questions?

Have they done any testing on annealing vs not? If so, did they find any measurable effects of work hardening that affects springback and neck tension? Is there a point where it shows up and can be reversed or aided by annealing, IE every, or other, or 3rd firing, etc. Case life?

I haven't done much annealing, but the few batches I've done I noticed the brass seemed to require more pressure and felt sticky going through the sizing die. Is there an explanation for that, and can it easily be resolved?

Thanks.

 

[BjornF16]

Podcasting with ADG tomorrow

Any questions?

Will they publish AMP annealing codes for specific lots like Peterson does?

 

[Gorp2007]

Podcasting with ADG tomorrow

Any questions?

Ask them if/when they’re coming out with the 6.8 WST brass, it’s a point of much debate in some of the 6.8 WST threads around here.

 

[260shooter]

Podcasting with ADG tomorrow

Any questions?

This might be a better general question for UM. ADG makes 7 RUM brass and 28 Nosler, why do you not here about peoples exploits with the 7 RUM? Watching the podcast, it doesn't seem hunters are afraid of over bore cartridges as long as goals are met. And there is good brass, powder and bullets to support it now.

 

[Mike D Texas]

When are they going to make 300 SAUM brass?


Sent from my iPad using Tapatalk Pro

 

[NevadaMike]

How about 22 ARC brass?

 

[wind gypsy]

What consideration goes into case web thickness, diameter, and "hardness" (probably a better word for this)? Primarily this question is in relation to a given piece of brass's proclivity to have clickers.

 

[Sadler]

Podcasting with ADG tomorrow

Any questions?

Why can’t they make fully formed 6UM brass?

 

[Grundy53]

Why can’t they make fully formed 6UM brass?

I would imagine they can. But there just isn't enough demand to make it profitable.

Sent from my SM-S901U using Tapatalk

 

[Ryan Avery]

Great podcast today with ADG got most of the questions answered.

 

[GoatPackr]

Great podcast today with ADG got most of the questions answered.

When will it be available to listen to?

Kris

 

[gabenzeke]

So I have all the makings for a 7 prc minus barrel and stock. Was planning on selling it and going to a 6mm of some flavor. But now I'm thinking I may go 6-7prc. Really anxious to hear how this one turns out.

Sent from my Pixel 6 Pro using Tapatalk

 

[GoatPackr]

So I have all the makings for a 7 prc minus barrel and stock. Was planning on selling it and going to a 6mm of some flavor. But now I'm thinking I may go 6-7prc. Really anxious to hear how this one turns out.

Sent from my Pixel 6 Pro using Tapatalk

He finished it. It was about the same as the 6UM.
You should go for it. You have most everything needed.

Kris

 

[gabenzeke]

He finished it. It was about the same as the 6UM.
You should go for it. You have most everything needed.

Kris

I'd still like to see load data. H1k to get roughly same velocity? If so, I'm all in.

Sent from my Pixel 6 Pro using Tapatalk

 

[GoatPackr]

I'd still like to see load data. H1k to get roughly same velocity? If so, I'm all in.

Sent from my Pixel 6 Pro using Tapatalk

I don't think you will get H1k to compete with Crack (N570)
It would be great to see the comparison.

Kris

 

[JBMAK]